







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why The Hammocks Homeowners Choose Toto Construction
We provide independent Toto construction and service in The Hammocks, Florida. That means we install, repair and remodel around Toto toilets and Washlet bidet seats every working week, with quality parts that fit the fixture and a written estimate that sets the price before anything comes off the wall. We’re not affiliated with Toto and hold no manufacturer authorization, so you get honest options from a local contractor instead of warranty scripting from a brand rep.
Most of what we do with Toto in The Hammocks runs through bathroom remodeling: replacing a tired suite, moving a fixture, converting a tub to a walk-in shower and reusing the toilet that still works. The Hammocks is a built-out Kendall-area community of 1980s and 1990s stucco-and-vinyl ranch homes, and much of the bathroom stock here is original. Those bathrooms are ready for a second life, and the plumbing in them deserves better than a bargain fixture. Toto bowls, tanks and electronic seats are ceramic and electronic goods, and they reward a careful install. Call (844) 797-9354 for a free estimate.
Why Trust The Hammocks Construction for Your Toto Construction?

Our technicians have up to 13 years of experience, and a good share of that has been spent on Toto fixtures. That matters because Toto products are built to tight tolerances. Rough-in dimensions, water-supply placement and clearance to the wall behind the bowl all have to land right the first time on a remodel, and they usually can’t be corrected after tile is set. We measure before demolition, not after.
We source quality parts that fit the equipment. Where sealing and electronics depend on exact tolerances, that means a genuine Toto fill valve, flapper, wax ring or Washlet component. For supply lines, stops and trim, a quality aftermarket part does the job fine and costs less. That’s a judgment call we make on each fixture, not a blanket policy.
Warranty-safe practice means we don’t drill into a glazed bowl, don’t substitute a part that changes how the flush or seat electronics behave, and don’t force a fit that puts stress on ceramic. If a fixture is under a manufacturer warranty, we’ll tell you what’s covered and what isn’t before we touch it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Toto Construction Problems We Fix in The Hammocks
- Washlet seats that stop spraying or stall mid-cycle in a humid bathroom. South Florida humidity works on the inlet solenoid valve and control board inside an electronic bidet seat. The seat goes dry, cycles on its own, or locks up halfway through a wash. It’s rarely the whole unit. A clogged inlet filter or a failing solenoid explains most of it.
- Phantom refilling on Drake and Ultramax tanks. The tank keeps topping itself up when nobody’s used the toilet, and the water bill quietly climbs. On a Drake two-piece the flapper or fill valve has lost its seal. On a one-piece Ultramax it often starts the same way, with mineral scale holding the seal open.
- Weak flushing from mineral scale in one-piece bowls. Our water is hard, and a one-piece gravity-flush toilet can lose its push over years as scale closes the rim jets and the bowl’s trapway. That’s not a part swap. It’s a descale, and sometimes an honest conversation about replacement.
- Wax-ring leaks and rocker movement from rough-in mismatch. Drop a Toto toilet onto an old 12-inch or offset flange and the bowl can sit proud or rock. A rocking bowl stresses the wax ring, the ring fails, and water shows up at the base. The fix starts at the flange, not the toilet.
- Lost CEFIONTECT glaze from abrasive cleaning. The slick glazed surface that keeps a bowl cleaner is a material, not a coating you can buff back. Scrubbing with an abrasive pad wears it thin and the bowl starts holding stains. We look at water chemistry and cleaning habits before we recommend a fix.
Here’s how this usually goes. A homeowner notices the toilet refilling on its own, or the bidet seat has quit spraying. On a Drake or Ultramax the usual culprit is a worn flapper or fill valve; a Washlet usually points to a clogged inlet filter or a failing solenoid. A qualified local technician pulls the tank, checks the flange and wax ring, descales the rim jets and CEFIONTECT surface, replaces the failed valve or seat component with the correct Toto part, and pressure-tests the supply before resetting the fixture. If the electronics board or a one-piece bowl is beyond economical repair, we’ll say so and quote a replacement instead of chasing discontinued parts.
Toto Parts & Our Repair-vs-Replace Approach

We’re not a Toto dealer and we don’t keep OEM parts on a shelf. We source the correct parts for your fixture, and we make the call on each one. Fill valves, flappers, wax rings and Washlet components are specified as genuine Toto parts, because the seal and the electronics depend on exact tolerances. Supply lines, stops and trim can come from a quality aftermarket maker without hurting anything.
The repair-or-replace question has a simple test. If a part swap restores the fixture’s flush, seal or wash function, we repair. If scale has closed the trapway of a one-piece bowl, or a Washlet control board has failed on an older seat, replacement is the honest call. Chasing discontinued electronics gets expensive fast. We’d rather tell you that plainly than sell you a string of parts.
If you’re weighing both options, call (844) 797-9354 for an estimate. We’ll spell out the fix and the replacement side by side before you decide.
Our Toto Service Process – Step by Step
- 1
Diagnosis. We test the flush, the fill and the seat electronics in your actual bathroom. On a remodel, we measure the rough-in, supply placement and clearance, and open the wall or floor as needed to check the flange.
- 2
Repair or install. A repair uses the correct part for that fixture. A new install sets the toilet on a sound flange with a new wax ring, and we plan the electrical and water supply for a Washlet before tile goes down.
- 3
Test. We cycle the flush several times, watch the tank for phantom fills, run every Washlet function and check the supply joints for any weep before we call it done.
- 4
Warranty and paperwork. You get the written estimate, the parts used, and a clear note on any manufacturer warranty that applies to the fixture.
See the difference
Before
After
Before
After
Before
AfterToto Products We Service & Install in The Hammocks

We work on Toto’s residential lineup, which is heavily ceramic and electronic. That covers two-piece and one-piece high-efficiency toilets, including the Drake and the Ultramax II, and the Washlet electronic bidet seats alongside integrated WASHLET+ models. We also handle the high-efficiency EcoPower and EcoPromenade models in remodel retrofits where the older fixture has to go and the new one has to meet the household’s water use.
Around the fixture, we install walk-in showers, vanities and full bathroom remodels. That’s the work where a Toto install lives, so the plumbing, tile and electric all get coordinated under one estimate instead of three separate contractors.
Hammocks-area HOA rules matter here too. Many subdivisions require architectural approval before the county permit, and plans get bounced for cosmetic reasons even when the engineering is fine. We plan for that approval step in the schedule, not after it holds up delivery.
We Also Service These Brands
We’re not limited to a single manufacturer. Alongside Toto work, we install and service Kohler plumbing fixtures, KraftMaid cabinetry, GAF roofing and PGT impact windows and doors in The Hammocks. That breadth means you can choose the material that fits your home and your budget, and we’ll handle the rest.
FAQs – Toto Construction Service in The Hammocks
No. We’re an independent Toto service provider, not a dealer or an authorized installer. We work with and around the brand on a daily basis, which means we can give you honest options rather than warranty scripting.
Yes. We specify genuine Toto fill valves, flappers, wax rings and Washlet components where the seal and the electronics depend on exact tolerances. Quality aftermarket parts are fine for supply lines and trim. We source what your fixture needs and tell you which is which.
A toilet repair or valve and flapper swap is usually finished in a single visit. A full bathroom remodel around it is a multi-week job, from demolition and rough-in through tile and fixture reset. We give you the timeline in the written estimate.
Two-piece and one-piece high-efficiency toilets, Washlet electronic bidet seats and integrated WASHLET+ models, and the high-efficiency EcoPower and EcoPromenade lines. We also install walk-in showers and vanities around them.
Not by itself. Proper installation and genuine parts protect it. Substituting parts that change how the flush or the seat electronics behave can affect a manufacturer warranty, and we’ll flag that before we start.
Typical estimated ranges for the projects we handle around Toto fixtures run from a vanity install up to a full bathroom remodel. These are estimates, and the written estimate sets the final price:
| Project | Typical estimated range |
|---|---|
| Full Bathroom Remodel | $9000 – $28000 |
| Small Bathroom Remodel | $5000 – $12000 |
| Walk-In Shower Installation | $4500 – $12000 |
| Tub-to-Shower Conversion | $3500 – $10000 |
| Bathroom Vanity Installation | $800 – $3000 |
Call (844) 797-9354 for an exact quote – estimates are free.
Yes, in most cases. A Washlet adds an electrical outlet, a supply connection and clearance behind the bowl, and the remodel is the right time to plan all three before tile is set. Ask us to check the seat clearance and rough-in before demolition.
The flapper or fill valve has lost its seal. It’s a common, simple fix on a two-piece tank. Pulling the flapper and checking for scale on the seat usually finds it in minutes. Call (844) 797-9354 to schedule the repair.
No. CEFIONTECT is part of the ceramic surface, not a coating that can be buffed back on. Abrasive scrubbing wears it thin, and there’s no reliable repair. Avoiding harsh pads protects it far better than replacing the bowl.
Yes. A one-piece toilet has no tank-to-bowl adjustment, so the rough-in, supply placement and clearance all have to be right before the fixture sets. Measure and check the flange against the old 12-inch or offset connection first. Get that wrong and you get a rocker and a leaking wax ring.
Usually yes, if the flange and wax ring are sound. Reusing it keeps a good fixture out of the landfill and saves you the cost of a new one. We inspect the flange and reset the toilet on a fresh wax ring as part of the conversion.
Book Your Toto Service in The Hammocks, FL
We repair, install and remodel around Toto fixtures across The Hammocks, from a single valve to a full bathroom rebuild. Estimates are free, and every quote is written line by line so the price is set before work starts. Call (844) 797-9354. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at The Hammocks Construction.












