







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why The Hammocks Homeowners Choose Cambria Construction
We provide independent Cambria construction service in The Hammocks, FL, handling quartz countertops, kitchen island tops, and backsplash installation that meet the brand’s fabrication and seam standards. What sets our Cambria work apart is focus: we know the brand’s colorways, slab formats, and edge profiles, we source through authorized distributors, and we set every seam with the color-matched adhesive the brand specifies. Call (844) 797-9354 for a free estimate.
Cambria is a quartz surface brand, and quartz is unforgiving of shortcuts. The material is dense, it resists staining on the surface, and it still chips, etches, and shows seam problems when fabrication is rushed. That’s the part most homeowners learn after the fact.
A few things worth knowing about how we work in The Hammocks. Our technicians have up to 13 years of experience with quartz surfaces, and we are an independent Cambria service provider, not affiliated with or authorized by Cambria. We can source the brand through authorized distributors and match it to an existing kitchen. We also handle KraftMaid cabinetry, Kohler fixtures, GAF roofing, and PGT windows when a countertop project turns into a bigger kitchen job.
Why Trust The Hammocks Construction for Your Cambria Construction?

Our technicians have worked with Cambria quartz long enough to recognize the difference between a seam that was set correctly and one that will show a ghost line in two years. That’s a narrow skill, and it’s the one that matters most on a quartz job.
Cambria surfaces are fabricated, not manufactured on site. The slab arrives finished; the quality of the finished countertop comes down to how it’s cut, edged, and joined. We work to the brand’s spec on seam adhesive selection, on edge-profile geometry, and on the water-fed polishing that keeps a high-silica surface from chipping at the sink cutout. When a Cambria-approved color-matched seam kit is the right material, that’s what we use. Generic epoxy cures to a different sheen and shows through light-colored slabs, and there’s no rework that fixes that cheaply.
Warranty-safe service means we protect what the brand stands behind. Cutting corners on tooling or skipping a proper back-bevel on a drop edge voids coverage you paid for. We don’t put a Cambria surface in that position. When a fabricator’s work is done right, the surface looks the way it should from day one through year ten. That’s the standard we hold in The Hammocks.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Cambria Construction Problems We Fix in The Hammocks
Quartz problems follow patterns. Here are the ones we see most often on Cambria surfaces in The Hammocks kitchens.
- Yellowed or visible seams on light-colored slabs. A seam set with generic epoxy instead of Cambria’s color-matched seam kit cures to a slightly different tone and sheen. On a light slab like Britannica, that difference reads as a faint yellow or gray line along the joint. It’s not a stain on the quartz; it’s the adhesive underneath showing through.
- Edge chipping at sink cutouts and drop edges. Cambria’s high-silica composition is dense and resists scratching, and it chips when a tool catches. Dull tooling, a missing water-fed polisher, or an edge that wasn’t back-beveled properly during fabrication all leave a weak spot that shows up months later, usually right where hands and dishes hit.
- Etching and dull spots on matte or honed finishes. Homeowners often assume quartz is stain-proof and reach for an acidic cleaner. On a matte or honed Cambria surface, that attack leaves a dull patch that won’t wipe away. It needs re-honing, not polishing.
- Surface scratches on dark colors. Dark slabs like Ella show scuffs and fine scratches that a light color would hide. Buffing the area can make it worse by changing the sheen in a patch. The right fix is a controlled re-hone across the whole surface.
- Seam separation and movement. South Florida’s humidity swings move cabinetry and substrate, and a seam that wasn’t set with a flexible, properly cured adhesive opens along the joint. Left alone, water gets into the seam line and the problem spreads.
Here’s how this kind of job usually goes. A homeowner notices a faint dark line along the seam of a Cambria Britannica island and a small chip at the sink edge after a few years of use. The usual cause is a seam that was set with generic epoxy and an edge that wasn’t properly back-beveled during fabrication. A qualified independent pro typically re-routs the seam, injects Cambria’s color-matched adhesive, and re-polishes the edge, matching the factory sheen without replacing the slab.
Cambria Parts & Our Repair-vs-Replace Approach

For Cambria work, we use Cambria-approved color-matched seam adhesive and the OEM edge profiles that fit the surface. Aftermarket epoxies are cheaper and they cure to a different sheen. On a dark slab that mismatch is subtle; on a light one it’s a ghost line you’ll see every morning.
Repair versus replace comes down to where the damage sits. A failed seam, a chipped edge, or a set of surface scratches is a targeted job: re-rout the seam, re-inject the adhesive, re-polish or re-hone the edge or face to match the factory finish. Full slab replacement only makes sense when a crack runs through the body of the stone, because no amount of polishing closes a structural break.
We don’t stock OEM or genuine Cambria parts, and we’re not a dealer. We source what the job needs through authorized distributors and tell you plainly which approach the surface will tolerate. If you’re looking at a seam or an edge and wondering whether it’s fixable, call (844) 797-9354. Estimates are free.
Our Cambria Service Process – Step by Step
- 1
Diagnosis. We look at the seam, the edge, and the finish under proper light, check the substrate and cabinet movement underneath, and identify whether the problem is adhesive, fabrication, cleaning damage, or structural.
- 2
Repair or install. For a seam we re-rout and inject color-matched adhesive; for an edge we re-bevel and re-polish with water-fed tooling to match the factory profile; for a new install we template, cut, and edge to Cambria’s spec.
- 3
Finish and test. We check the seam under raking light at several angles, confirm the sheen across the whole surface reads evenly, and run a hand along every edge for a consistent profile.
- 4
Warranty and care. We leave you with the care guidance for your specific finish and confirm what the work covers, so your Cambria warranty stays intact.
See the difference
Before
After
Before
After
Before
AfterCambria Products We Service & Install in The Hammocks

We handle the full range of Cambria quartz surfaces for a residential kitchen: slab countertops in the brand’s colorways, waterfall and standard edge profiles, kitchen island tops, and backsplash panels. We work with the recognized palette, from Britannica and Torquay to Whitehall and Ella, and we can source additional colorways through authorized distributors.
We also do the cabinetry and fixture side of the same kitchen, with KraftMaid and Wellborn cabinet lines and Kohler fixtures, so the countertop isn’t waiting on three other trades to catch up.
In The Hammocks, that coordination matters because most of this work runs through a homeowners association and county permitting tied to Florida’s High-Velocity Hurricane Zone rules. Many subdivisions here require architectural approval before the county permit is issued, and plans get bounced for cosmetic reasons even when the engineering is fully compliant.
We Also Service These Brands
We’re not a single-brand shop. Alongside Cambria, we work with KraftMaid cabinetry, Kohler plumbing fixtures, GAF roofing systems, and PGT windows and doors. If your kitchen project turns into new cabinets, a fixture upgrade, or a window replacement while the wall is open, we can carry it in one relationship instead of handing you off.
FAQs – Cambria Construction Service in The Hammocks
No. We are an independent Cambria service provider. We are not affiliated with, authorized by, or a dealer for Cambria, and we don’t claim factory certification. What we do is install, repair, and service Cambria quartz surfaces to the brand’s fabrication and seam standards, sourcing through authorized distributors. Call (844) 797-9354 to talk through your job.
Yes. For Cambria work we use Cambria-approved color-matched seam adhesive and OEM edge profiles that fit the surface. We don’t stock or carry genuine Cambria parts, and we don’t substitute aftermarket epoxy on visible seams, because it cures to a different sheen and shows through lighter slabs. Call (844) 797-9354 to schedule a free estimate.
A seam repair or edge re-polish is usually a single visit. A new Cambria install runs longer because it involves templating, fabrication, and likely a permit and HOA architectural review, and South Florida permits tied to storm season can stretch that timeline. Call (844) 797-9354 for a realistic estimate for your job; estimates are free.
We cover Cambria quartz for countertops, kitchen island tops, waterfall and drop edges, backsplash panels, and the re-polishing and re-seaming that these surfaces need over time. We handle the fabrication and finish side of the surface, and we coordinate cabinets and fixtures when the kitchen scope includes them. Call (844) 797-9354 to confirm your product.
Not if the service is done to the brand’s spec. We use color-matched seam adhesive, OEM edge profiles, and proper water-fed polishing to protect what the brand stands behind. Generic epoxy, dull tooling, or skipping a back-bevel on a drop edge is what puts coverage at risk. Call (844) 797-9354 and we’ll walk through your surface before any work starts.
Countertop installation typically runs $2,000 – $6,500, a kitchen island installation $3,000 – $10,000, and a backsplash installation $800 – $2,500. These are typical estimates for The Hammocks; the written line-item estimate sets the final price. Call (844) 797-9354 for an exact quote, free of charge.
| Service | Typical estimated range |
|---|---|
| Countertop installation | $2,000 – $6,500 |
| Kitchen island installation | $3,000 – $10,000 |
| Backsplash installation | $800 – $2,500 |
No change orders, no surprises in the middle of the job. The written estimate is the price.
Yes. A yellowed seam is almost always a generic epoxy that cured to the wrong tone, and it can be re-routed and re-injected with Cambria’s color-matched adhesive and re-polished to the factory sheen. Slab replacement is only needed when a crack runs through the body of the stone. Call (844) 797-9354 for a free estimate on a seam repair.
Cambria quartz itself handles South Florida humidity well; it doesn’t absorb water. The care issue is acidic cleaners, which etch matte and honed finishes, and seam movement from humidity-driven cabinet shifts. Keep the surface clean with a mild cleaner and check your seams once a year. Call (844) 797-9354 if a seam has opened.
Cambria offers a range of edge profiles for islands, and most can be re-polished after chipping or scuffing, provided the original edge wasn’t back-beveled too thin. A qualified pro re-bevels and re-polishes with water-fed tooling to match the factory profile. Call (844) 797-9354 to have an edge checked.
It can be, if the drywall is sound, dry, and the substrate can support the panel weight; in a humid South Florida kitchen, water-damaged drywall behind a backsplash needs to come out first. We check the substrate before quoting the install. Call (844) 797-9354 for a free estimate.
Match by colorway, not by batch. Cambria’s colorways are consistent over time, so a new Britannica or Whitehall island top will sit next to older slabs from the same colorway, and the seam and edge work matter more than the material date. We source through authorized distributors to confirm availability. Call (844) 797-9354 to talk through matching.
Book Your Cambria Service in The Hammocks, FL
If you have a Cambria surface that’s chipped, showing a seam, or ready for a fresh installation in The Hammocks, call (844) 797-9354 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at The Hammocks Construction.












